Кстати в Алкиде после проверки диска в DOS грязная метка снимается, но при загрузке винды с харда система валится в ошибку без проверки диска, а потом грязная метка появляется вновь (fat32 появлению не мешает).
Из txt:
smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen,
http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD series (80 GB and above)
Device Model: TOSHIBA MK1234GSX
Serial Number: 963H0165T
Firmware Version: AH001A
User Capacity: 120 034 123 776 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Nov 17 01:31:59 2010 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 435) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 86) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1417
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 3150
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 083 083 000 Old_age Always - 7024
10 Spin_Retry_Count 0x0033 162 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2844
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 75
193 Load_Cycle_Count 0x0032 081 081 000 Old_age Always - 196457
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 44 (Lifetime Min/Max 14/73)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 1
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 8298
222 Loaded_Hours 0x0032 086 086 000 Old_age Always - 5835
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 444
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 7 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 7 occurred at disk power-on lifetime: 6899 hours (287 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 3f 50 71 e3 Error: ICRC, ABRT 1 sectors at LBA = 0x0371503f = 57757759
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 3d 4e 71 e3 00 01:48:17.535 READ DMA
c8 00 40 fd 16 71 e3 00 01:48:17.528 READ DMA
c8 00 40 fd 0b 71 e3 00 01:48:17.524 READ DMA
c8 00 40 bd ec 70 e3 00 01:48:17.518 READ DMA
c8 00 40 7d 1a 6f e3 00 01:48:17.515 READ DMA
Error 6 occurred at disk power-on lifetime: 5111 hours (212 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 4b c5 ba e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00bac54b = 12240203
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 d0 08 49 c3 ba e0 00 00:07:40.805 READ DMA
c8 d0 08 41 c1 ba e0 00 00:07:40.804 READ DMA
c8 d0 08 39 c1 ba e0 00 00:07:40.804 READ DMA
c8 d0 08 31 c1 ba e0 00 00:07:40.804 READ DMA
c8 d0 08 29 c1 ba e0 00 00:07:40.804 READ DMA
Error 5 occurred at disk power-on lifetime: 4613 hours (192 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 20 76 d4 d6 e3 Error: AMNF at LBA = 0x03d6d476 = 64410742
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c4 03 40 49 d4 d6 e3 00 00:09:24.495 READ MULTIPLE
ef 03 45 01 55 aa a0 00 00:09:24.494 SET FEATURES [Set transfer mode]
ef 03 0c 01 55 aa a0 00 00:09:24.494 SET FEATURES [Set transfer mode]
c6 00 10 01 55 aa a0 00 00:09:24.494 SET MULTIPLE MODE
91 00 3f 01 55 aa af 00 00:09:24.493 INITIALIZE DEVICE PARAMETERS [OBS-6]
Error 4 occurred at disk power-on lifetime: 4613 hours (192 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 60 76 d4 d6 e3 Error: AMNF at LBA = 0x03d6d476 = 64410742
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c4 03 80 49 d4 d6 e3 00 00:08:34.029 READ MULTIPLE
ef 03 45 01 55 aa a0 00 00:08:34.029 SET FEATURES [Set transfer mode]
ef 03 0c 01 55 aa a0 00 00:08:34.028 SET FEATURES [Set transfer mode]
c6 00 10 01 55 aa a0 00 00:08:34.028 SET MULTIPLE MODE
91 00 3f 01 55 aa af 00 00:08:34.028 INITIALIZE DEVICE PARAMETERS [OBS-6]
Error 3 occurred at disk power-on lifetime: 4613 hours (192 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 20 76 d4 d6 e3 Error: AMNF at LBA = 0x03d6d476 = 64410742
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c4 03 40 49 d4 d6 e3 00 00:19:00.842 READ MULTIPLE
ef 03 45 01 55 aa a0 00 00:19:00.842 SET FEATURES [Set transfer mode]
ef 03 0c 01 55 aa a0 00 00:19:00.841 SET FEATURES [Set transfer mode]
c6 00 10 01 55 aa a0 00 00:19:00.841 SET MULTIPLE MODE
91 00 3f 01 55 aa af 00 00:19:00.841 INITIALIZE DEVICE PARAMETERS [OBS-6]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 7002 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.